This case is the Mesh version of the straightforward yet stylish Nova Midi-Tower with Tempered Glass and an additional focus on air cooling. This variant implements a front section that consists entirely of a fine mesh metal grille to enable the maximum possible airflow. In spite of the fine mesh, the brightly illuminated fans installed behind it remain visible from the outside. The front panel includes the typical BitFenix logo on the front and features three pre-installed 120 mm fans, while the fourth is placed at the back. All four fans have digitally addressable RGB-LEDs. Furthermore, users will appreciate the presence of two 3,5" slots, two 2,5" slots as well as the possibility of installing additional fans if needed. The Bitfenix Nova Mesh offers plenty of space for the majority of common configurations. The Highlights of the BitFenix Nova Mesh A-RGB TG Midi-Tower: New version of the popular Nova TG Midi-Tower with fine mesh front panel Tinted, tempered glass side, motherboards up to a E-ATX formfactor Supports gaming GPUs up to 36 cm in length Slots for 3x 120 mm- or 2x 140 mm fans in the front and 2x 120 in the roof Four pre-installed fans with digitally addressable RGB LEDs Space for 240 mm radiator in roof and up to 280/360 radiator in front Space for 2x 3,5/2,5- and 3x 2,5" drives BitFenix Nova Mesh A-RGB TG: Sleek Midi-Tower in White The front panel, with its fine mesh grill, makes the case perfect to meet the challenges of providing a steady stream of fresh air for high-end gaming hardware while still looking good. The result is that airflow is maintained without compromising on aesthetics. Quite to the contrary, the case cuts an elegant and timeless figure and stands out from the competition. The clean lines and sleek design not only look good, they fulfil a purpose: The BitFenix Nova Mesh A-RGB TG keeps out unwanted dust while also minimising noise. BitFenix’s modern approach to design also means that the motherboard is located towards the top of the case and the power supply at the bottom. This offers the advantage of giving power supplies a separate supply of clean, fresh air through the bottom of the case to help minimise the transfer of heat to other internal components. A dust filter protects the PSU from dust and dirt, also helping to minimise the possibility of overheating over time. A shroud for the PSU conceals any messy cabling that would otherwise be visible through the tinted tempered glass. Plenty of Space for Well-Cooled Hardware A large cut-out in the motherboard tray enables users to benefit from convenient and easy installation of their CPU cooler. Expansion cards can be installed using the (easily removed) screws. Two internal 2,5/3,5" slots are available in the HDD cage beneath the PSU shroud. Two 2,5" drives are located on the rear of the motherboard tray, an additional drive can be screwed onto the PSU shroud. All in all, the case offers an impressive amount of space for full-size hardware components. The case’s cooling is catered for by up to three 120- or two 140 mm fans in the front. Additionally, the roof offers space for two additional 120 mm fans. There are four pre-installed 120 mm fans with digitally addressable RGB-LED lighting from BitFenix’ Spectre Series, one in the rear and three in the front that ensure heat is exhausted and dissipated efficiently. Thanks to the fine mesh front and dust filter in the roof, the interior is sure to remain clean and dust-free over time. Of course, if you prefer, you can also use compatible radiators instead of fans - with a 360- or a 280 in the front. The top of the case reserves just enough space for a 240 mm radiator, but please be sure to check with the manufacturer beforehand. The I/O panel located on top of the case towards the front includes two USB 3.0- and two audio ports. This is complemented by the inclusion of a power- and reset switch. Technical Details: Dimensions: 201 x 437 x 465 mm (W x H x D) Material: Steel, ABS plastic, tempered glass Colour: White Weight: 5.3kg Form factor: E-ATX (up to 272 mm), ATX, Micro-ATX, Mini-ITX Fans possible: 3x 120 mm / 2x 140 mm (Front) 2x 120 mm (Roof) 1x 120 mm (Rear) Pre-installed: 3x 120 mm (Front, digitally addressable RGB-LEDs) 1x 120 mm (Rear, digitally addressable RGB-LEDs) Radiators possible: 1x max. 360/280 mm (front) 1x max. 240 mm (roof) 1x max. 120 mm (rear) Drives: 2x 2,5/3,5" (internal) 3x 2,5" (internal) Extension slots: 7 I/O Panel: 2x USB 3.0 1x HD-Audio In/Out 1x Power Button 1x Reset Button Power supply: Standard PS2 ATX format (optional) Maximum graphics card length: 360mm Maximum CPU cooler height: 160mm Maximum power supply length: 220mm